Inhaltsverzeichnis   MOBOTIX Online-Hilfe

General Image Settings

Open the General Image Settings dialog to define the basic settings for image control in the camera.


Description of Parameters

Camera Selection Select the lens that you want see on the Live and Guest screens or set the picture-in-picture mode to combine the images of both lenses (only for dual-lens cameras).
right Right lens (factory default setting, usually the wide-angle lens)
Left Left lens (usually the tele lens)
Both Combines the images of both lenses and displays them side-by-side (left: left lens, right: right lens, as seen by the camera). This option is not available on Day/Night models as these models automatically switch between the daylight and night image sensors depending on illumination.
Auto Automatically selects the color sensor for daylight and the b/w sensor for night recording (only for Day/Night cameras).
Image Size

Select the display size of the image.
Dual images (right and left image sensor) automatically require twice the width.

When selecting Custom Size, the camera will use the image size specified in the Custom Size field (see below).

Camera Night Switch (DY/NI)
(only Day&Night Models)

Day/Night camera models automatically switch between day and night lenses when the illumination falls below or exceeds the level set here. The higher the illumination value, the earlier the camera switches to the night lens.


  • This parameter is available only for Day/Night models.
  • Set the night switch delay to the desired value. This delay prevents switching to the other lens when illumination increases or decreases for a short period of time (e.g. a car with headlights passing by at night).

To determine the best possible value for defining the night camera level, proceed as follows:

  • Click on the More button at the bottom of the Text & Display Settings dialog to display all options.
  • In the same dialog, set the Text Display parameter to On.
  • In the Comment text box, enter the ^IR placeholder. The camera now displays the current illumination rate in Lux on the live image.
    (See also Placeholders for Dynamic Image Text.)
  • Set the Level Meter parameter to Bar, and select Illumination as source for the level meter. The camera now displays the current exposure rate as a red bar on the live image. The value for switching to the night lens is displayed as white vertical line.
Camera Time Switch
(all other models with dual lenses)

Switches to the other lens according to a Time Table, if the Camera Selection option has been set to auto.

If a time table profile is active or on (the symbol is visible), the camera uses the left image sensor. If the time table profile is not active or off, the camera will use the right image sensor.

Custom Size
(only displayed if Image Size has been set to Custom Size)

Enter the size of the customized image in pixels that is displayed if Resolution has been set to Custom Size. If the image size defined here has a different ratio than 4:3, you can click with the mouse near the borders of the image to move the image area within the standard image in the desired direction (panning).

It is recommended to set the coordinates of the custom size by creating a yellow frame on the live image of the camera and copying them into the required field. For additional information on this topic, see the Graphically Entering Image Areas help page.

If you have selected Custom Size, you can also crop the image. This feature will define a specific portion of the image, which will then be used for all other operations. This feature also allows an interactive definition of the yellow rectangle in the image. Next, clicking on the Adjust Custom Size button will adjust the image size to match the ratio of the selected image area, thus displaying the whole image at once.

Image quality

Select the desired ratio of image quality to frame rate:

  • High: Read full image sensor to deliver the best image quality.
  • Normal: Good image quality with high frame rates (this is the default setting).
  • Fast: Highest frame rate with some loss in quality.
Frames per second Number of images per second that are recorded by the camera. If long exposure times are necessary to comply with poor lighting conditions, the frame rate decreases.
Display Mode

Sets the display mode of the selected image sensor:

  • Full Image: Shows the full image of selected image sensor. When using a 180° (Fisheye) lens, the uncorrected (distorted) image is round with black borders.
  • Normal: Shows a corrected image from Q2x cameras in 4:3 format (i.e. not Panorama).
  • Lens Correction: Shows a corrected image in 4:3 format (i.e. not Panorama) from all other cameras that allow activating lens correction (except Q2x).
  • Picture-in-Picture: Displays a small preview image inside of the other lens in the main image. If the resolution is lower than VGA (640x480 pixels), the camera suppresses the preview image.
  • Picture in Zoom: Displays a small overview image in the zoomed image. If the resolution is lower than VGA (640x480 pixels), the camera suppresses the preview image.
  • Event in Picture: Displays the last event image in the live image. If the resolution is lower than VGA (640x480 pixels), the camera suppresses the preview image.
  • Surround: Displays four images with independent views. This mode is not available if both image sensors are used side-by-side!
  • Panorama: Shows a corrected image in 8:3 format. This view mode shows a special 180° image.
  • Double Panorama: Shows two corrected images, which will be displayed differently depending on where the camera has been mounted:
    • Ceiling mounted: Shows two 180° views in a special projection, thus providing for full 360° surveillance. The upper image section shows "North" exactly at the center of the image (as set using the Installation Quick Control; the lower image section shows the opposite direction. Furthermore, the viewing directions of both images are linked with the second image trailing the first by 180 degrees. Note that you cannot change the tilt angle of this image as this disturb the image geometry of the projection.
    • Wall-mounted: Displays two Panorama 180° views pointing in the same direction.
  • Panorama/Focus: Consists of one panorama image in 8-to-3 format and two corrected 4-to-3 images below.


  • The view modes described above depend on your camera model and may thus not be available in all cameras!
  • The width and height of the inset images are always a quarter of the width and height of the main image. The Enlarge inset image option in the General Image Settings dialog doubles the width and height of the inset image. The Position of the inset image options in the same dialog specify where the inset image will be displayed within the overall image.
  • The Panorama display modes provide the OnScreen Control, which allows panning, tilting and zooming the corresponding Panorama window. This element also controls the trapezoid correction used for adjusting the perspective of the image.
Mirror & Rotate Image

Using these parameters, you can mirror the image (but not the displayed text) in horizontal and vertical direction or turn it by 180°.


This feature is not available for display modes with lens correction!

  • When mounting MOBOTIX M12 or M2x cameras upside-down in outdoor scenarios, the cameras loose their IP65 certification!
  • When mounting the MOBOTIX M12 upside-down in outdoor scenarios (even though the camera is protected from rain), humidity from natural condensation cannot exit the camera properly. This will inevitably cause water to collect in the camera, leading to irreparable damages!
  • Mounting a MOBOTIX M12 upside-down in outdoor environments will automatically void your warranty!
Sharpness In order to improve image quality, you can adjust the sharpness control value. A lower value results in a smoother (less crisp) image. The factory default setting is 4.
Image Noise Suppression

Growing darkness may result in the image quality getting poorer because of image noise.
The Noise Suppress parameter minimizes this effect:

  • Off: Deactivates the noise suppression.
  • Low: As darkness grows, the camera will use temporal filtering and will reduce sharpness and color saturation (default setting).
  • High: As darkness grows, the camera will use spatial filtering in addition.
Obscure Image Area (OA)

In some applications, certain image parts need to be obscured. Activate this parameter and select a Time Table, the Obscure Image Color and the area that is to be covered.

Note: This parameter is available only for Secure models.

Obscure Image Time Table

Select a Time Table profile to activate/deactivate the obscured image areas in a scheduled manner.

Obscuring Image Areas

Defines the image areas that are to be obscured; every line in the definition box (e.g. 0,270,190,100,100,2) represents one window. The image coordinates' origin is the lower left corner of the image.

Format of one line:
lens, pos. x, pos. y, width, height, type

Parameters of one configuration line:

Image Sensor 0 = right
1 = left
Pos. x Number of pixels from the left edge of the image to the left edge of the window
Pos. y Number of pixels from the lower edge of the image to the lower edge of the window
Width Width of the window in pixels.
Height Height of the window in pixels.
Type 0 = filled rectangle
1 = crossed-out frame
2 = mosaic (default)
Hint: For defining a new or additional window, follow the instructions in the Graphically Entering Image Areas help page.

Konfiguration sichern

Klicken Sie auf Setzen, um die Einstellungen zu aktivieren und bis zum nächsten Neustart der Kamera zu sichern.

Beenden Sie den Dialog durch Klick auf Schließen. Hierbei wird geprüft, ob Änderungen der Gesamtkonfiguration vorliegen. Ist dies der Fall, werden Sie gefragt, ob die Gesamtkonfiguration dauerhaft gesichert werden soll.

de, en

© 2001-2024 MOBOTIX AG, Germany ·